smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.11.3-unRAID] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3750640AS Serial Number: 5QD2385K Firmware Version: 3.AAE User Capacity: 750,156,374,016 bytes [750 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Wed Jun 14 21:21:05 2017 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 202) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 116 083 006 Pre-fail Always - 103231894 3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 91 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 10 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 297746701 9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 4333 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 108 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 258 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 068 039 045 Old_age Always In_the_past 32 (0 182 32 29 0) 194 Temperature_Celsius 0x0022 032 061 000 Old_age Always - 32 (0 20 0 0 0) 195 Hardware_ECC_Recovered 0x001a 062 048 000 Old_age Always - 35115261 197 Current_Pending_Sector 0x0012 076 075 000 Old_age Always - 494 198 Offline_Uncorrectable 0x0010 076 075 000 Old_age Offline - 494 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 51 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 2351 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2351 occurred at disk power-on lifetime: 4259 hours (177 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 20 5f fe 72 40 Error: IDNF at LBA = 0x0072fe5f = 7536223 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 00 20 5f fe 72 40 00 04:12:12.270 READ VERIFY SECTOR(S) EXT 00 00 20 00 00 00 00 04 04:12:09.050 NOP [Abort queued commands] 42 00 20 3f fe 72 40 00 04:12:09.049 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:05.829 NOP [Abort queued commands] 42 00 40 ff ff 72 40 00 04:12:28.373 READ VERIFY SECTOR(S) EXT Error 2350 occurred at disk power-on lifetime: 4259 hours (177 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 20 3f fe 72 40 Error: IDNF at LBA = 0x0072fe3f = 7536191 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 00 20 3f fe 72 40 00 04:12:12.270 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:09.050 NOP [Abort queued commands] 42 00 40 ff ff 72 40 00 04:12:09.049 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:05.829 NOP [Abort queued commands] 42 00 40 bf ff 72 40 00 04:12:05.829 READ VERIFY SECTOR(S) EXT Error 2349 occurred at disk power-on lifetime: 4259 hours (177 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 40 ff ff 72 40 Error: IDNF at LBA = 0x0072ffff = 7536639 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 00 40 ff ff 72 40 00 04:12:12.270 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:09.050 NOP [Abort queued commands] 42 00 40 bf ff 72 40 00 04:12:09.049 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:05.829 NOP [Abort queued commands] 42 00 40 7f ff 72 40 00 04:12:05.829 READ VERIFY SECTOR(S) EXT Error 2348 occurred at disk power-on lifetime: 4259 hours (177 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 40 bf ff 72 40 Error: IDNF at LBA = 0x0072ffbf = 7536575 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 00 40 bf ff 72 40 00 04:12:12.270 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:09.050 NOP [Abort queued commands] 42 00 40 7f ff 72 40 00 04:12:09.049 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:05.829 NOP [Abort queued commands] 42 00 40 3f ff 72 40 00 04:12:05.829 READ VERIFY SECTOR(S) EXT Error 2347 occurred at disk power-on lifetime: 4259 hours (177 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 40 7f ff 72 40 Error: IDNF at LBA = 0x0072ff7f = 7536511 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 00 40 7f ff 72 40 00 04:12:12.270 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:09.050 NOP [Abort queued commands] 42 00 40 3f ff 72 40 00 04:12:09.049 READ VERIFY SECTOR(S) EXT 00 00 40 00 00 00 00 04 04:12:05.829 NOP [Abort queued commands] 42 00 40 ff fe 72 40 00 04:12:05.829 READ VERIFY SECTOR(S) EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4333 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.